RAM Beam Design: Connection Check
Hello everyone,In my model, I want to run a connection check (not through the RAM Connection module, but just through RAM Beam Design) for both beam-to-beam and beam-to-column conditions. I have a...
View ArticlePurchase Book
I want to purchase STAAD PRO CONNECT EDITION - SEISMIC ANALYSIS USING IS-1893 (PART-1)-2016 AUTHOR - SANJIB DAS . Please send me the detail of pricing and mode of purchase Hard copy / e-copy etc
View ArticleClik here to view.
STAAD Foundation Advanced Soil Shear Strength Parameter
Where is the soil shear strength parameter used in STAAD Foundation Advanced? Nothing in the manual describes how this parameter is used. This would be for an isolated footing job.
View ArticleRAM Elements Errors
Hello,See attached RAM Elemencommunities.bentley.com/.../5282.Shear-Wall-2.mswcommunities.bentley.com/.../0121.Shear-Wall-2.pdft CMU module file, for inplane shear wall check. It reports that the wall...
View ArticleQuery about difference in results
Sir,I analysed same model and same loading in three different way:1. I added PERFORM ANALYSIS and CHANGE command after every seismic load and used load combination and run P Delta analysis:STAAD...
View ArticleConnection between beam elements
HiI have a question regarding the connection between beam elements. I need to ensure that the elements that make up a pylon that I am modelling, are rigidly connected. Is this already the case when i...
View ArticleRam Concept - Design Strip
Hi,Can I have the end of a design strip supported by another perpendicular column strip between two column ? Usually we draw the design strip connecting two supports (columns). But in some cases I...
View ArticleClik here to view.
Wind load not generating with area that have more than 4 members
Hello,I am updating an existing warehouse and the wind load generator does not seem to be applying where there is more than 4 members making an enclosed space. Please see the picture for reference. Any...
View Articlehow do we apply different Multilinear spring values to Kx, Ky and Kz...
I am modeling a concrete shaft liner , the loading is due to water pressure which creates compression and uplift, the liner is confined by secant piles, how would I model the springs of each wall node...
View ArticleRCDC is unable to read data from staad file
I am using Staadpro connect edition version 22 and RCDC connect edition version 9. RCDC is not reading data from staad file. Kindly advise what to do.
View ArticleClik here to view.
Plate connections between beams in global model
Hello,I have a connection where a HHS member is fixed to a W beam flange, see attached. In between there is a 1/2' plate. What is the best way to model this connection in STAAD PRO? I have used the...
View ArticleAbout Floor Diaphragm and Reference load
Sir,I created a model with Floor Diaphragm and reference load command as follows:STAAD SPACESTART JOB INFORMATIONENGINEER DATE 21-Apr-20END JOB INFORMATIONINPUT WIDTH 79UNIT FEET KNJOINT COORDINATES1 0...
View ArticleClik here to view.
Bentley Ram does not launch from Staad Pro
I try to launch Bentley Ram from Advanced Slab design in Staad Pro Connect, it gives this message and i have no clue on how to rectify it.
View ArticleColumns failed due to EC 6.2.9 (2/3)
Hi, i did a portal frame model. However, staad pro analysis result shows that my column failed due to Clause EC 6.2.9 (2/3). i had try to put some restraints on the column as it is supported by the...
View Articleunable to display utilization table
Hello, I am unable to display the utilization table in STAAD V.22. I do not have the option to display it. The utilization ratio layout option is not highlighted under beam results in post-processing....
View ArticleRAM Beam design Module stops running
My Beam Design module appears to work through the design for levels 3-6, however when it reaches some point in the level 2 checks, in stops abruptly. I have run the integrity checks in the modeler, and...
View ArticleShut Down Computer after analysis is done
My model consists of 35000 odd plates.Is there any command to shut down the PC once the model analysis is done.
View ArticleWrong plate numbers and results while using OpenStaad functions for...
Hi,I have been using Excel VB macro for extraction of plate results from STAAD Connect using Open STAAD functions.It works fine (extracts the plate center stresses of the selected cells). However at...
View Articlewhile designing steel structure by Indian code warning comes...
while designing steel structure by Indian code warning comes Exceptional[Access violation raised! Aborted Analysis . What is this for? How to resolve it?
View ArticleClik here to view.
[Ram Concept] Error ABoundaryShape2D
Hi All,I encounter an issue with Ram Concept V8 Update 1 - Version 08.01.00.027. The model, which was created by Ram Concept V8.0 - Version 08.00.00.19, cannot run, but shows the error as per the...
View Article